设为365bet官网地址    收藏365bet官网地址

华彩光电365bet官网地址
      产品列表
预制件塑料模具
光伏墩模具
炕板模具
便道砖模具
井盖模具
365bet亚洲官方投注
365bet亚洲官方投注
屋檐板模具
水泥盖板模具
边沟盖板模具
      资质荣誉
      联系365bet
保定365bet官网地址
地址:保定市城东工业区
电话:18803129528
传真:0312-8103818
邮箱:107108222@qq.com
最新资讯

路基盖板模具的施工技巧

路基盖板模具作为热销产品之一,它的优势体现在生产效率很高,脱模迅速,生产起来非常有保障。而且盖板模具较低,但是质量却是非常棒,可以说是物超所值。路基盖板模具,高速路基盖板模具,水泥路基盖板模具生产水泥砖是时代进步的体现,也是工艺进步要求的表现,使用先进的盖板模具加工制品,具有很大的优势,而且比传统模具寿命高,可以生产数次,尤其是一些高要求的模具,寿命往往超过几百万次,如果这样的模具平均使用下来,成本也就会很低了。

As one of the hot-selling products, the advantage of the roadbed cover plate mold lies in its high production efficiency, rapid demoulding and very guaranteed production. Moreover, the die of the cover plate is low, but the quality is very good, which can be said to be worth more. The production of cement brick by roadbed cover plate mold is the embodiment of the progress of the times and the performance of the requirements of technological progress. The use of advanced cover plate mold for processing products has great advantages, and its service life is higher than that of traditional mold. It can be produced several times, especially for some high-demand molds, whose service life is often more than several million times. If such molds are used on average, the cost will be very low Now.

路基盖板模具必须挂通线进行施工,按侧平面顶面示高标线绷紧,按线码砌侧平石,侧平石要安正,切忌前仰后合,侧面顶线顺直圆滑平顺,无高低错牙现象,平面无上下错台、内外错牙现象。路基盖板模具必须座浆砌筑,座浆必须密实,严禁塞缝砌筑;沟盖板模具接缝处错位不超过1mm;侧石和平石必须在中间均匀错缝。沟盖板模具侧平石应保证尺寸和光洁度满足设计要求。外观美观,对弯道部分侧石应按设计半径专门加工弯道石,砌筑时保证线形流畅、圆顺、拼缝紧密。弧形侧石必须人工精凿后抛光处理。沟盖板模具后背应还土夯实,夯实宽度不小于50mm,厚度不小于15mm。沟盖板模具勾缝:勾缝时必须再挂线,把侧石缝内的杂物剔除干净,用水润湿,然后用1:3水泥砂浆灌缝填实勾干,侧平石勾缝、安砌后适当浇水养护。路基盖板模具必须挂通线进行施工,按侧平面顶面示高标线绷紧,按线码砌,切忌前仰后合,侧面顶线顺直圆滑平顺,无高低错牙现象,平面无上下错台、内外错牙现象。

The mould of subgrade cover plate must be hung with a through line for construction. It shall be tightened according to the height mark on the top surface of the side plane. The side flat stone shall be built according to the line code. The side flat stone shall be installed correctly. It is forbidden to close the front and back. The top line of the side shall be straight, round and smooth without high and low staggering, and the plane shall be free of up and down staggering, internal and external staggering. The mould of subgrade cover plate must be built with mortar, and the mortar must be dense, and it is strictly prohibited to block the joint; the dislocation of the mould joint of ditch cover plate shall not exceed 1mm; the side stone and flat stone must be evenly staggered in the middle. The side flat stone of groove cover plate mould shall ensure that the size and finish meet the design requirements. The appearance is beautiful, and the side stone of the curve section shall be specially processed according to the design radius, to ensure smooth line, smooth circle and tight joint during masonry. The curved side stone must be chiseled and polished manually. The back of the ditch cover plate mould shall be compacted with soil, the width of compaction shall not be less than 50mm, and the thickness shall not be less than 15mm. Joint pointing of ditch cover plate mould: during joint pointing, the line must be hung again, the sundries in the side stone joint shall be removed, wetted with water, and then filled with 1:3 cement mortar to dry the joint, and the side flat stone joint shall be pointed and watered properly for curing after installation. The mould of subgrade cover plate must be constructed by hanging a through line. It should be tightened according to the high mark line on the top surface of the side plane. It should be built according to the line code. It is forbidden to put the front and back together. The top line of the side should be straight, smooth and smooth, without high and low staggering teeth, and there should be no up and down staggering platform, internal and external staggering teeth on the plane.


【上一个】 365bet官网地址的详细生产过程 【下一个】 水沟盖板模具的产品优势


 · 路基盖板模具的施工技巧

|流水槽钢模具|防撞墙模具|排水沟模具|隔离墩模具|
XML 地图 | Sitemap 地图